KC-8 CW Cable Set for VK-64 with 1/8" plugĬanada Shipping is $11.00 per order International Shipping is $36. KC-4 CW Cable Set for VK-64 with 1/4" plug Doug has ported the FlexAPI to the Mac which allowed the development of xVoiceKeyer and for Mario (D元LSM) xDax and xCat. The program was renamed xVoiceKeyer in recognition of Doug (K3TZR) the developer of xLib6000. The SDR Voice Keyer for SmartSDR has been renamed to xVoiceKeyer and updated for SmartSDR 2.51 and above. Model KC-8 is terminated with a 1/8" plug. xVoiceKeyer (fka SDR Voice Keyer) for Mac version 3.01 released. Model KC-4 has the transmitter cable terminated with a 1/4" stereo Paddle cable has connector to the VK-64 on one end and stripped and tinned Includes cables to the paddle and transmitter. Length: 36" - Transmitter section, 30" Microphone section.
Email for pricing information on completely assembled and custom length cables. Specify 4 (VKC-4) or 8 (VKC-8) pin microphone connectors. The wires to these connectors come pre-stripped and tinned for quick and painless final assembly to match the pin out requirements for your particular equipment. The VKC-4/8 cables provide the connection between the VK-64 and your rig and microphones. Rear Panel Connectors & Controls Power: Center positive Transmitter and Microphone Audio: DB9 Computer: DB25 CW Paddle: 1/8" Stereo Phono CW Out: RCA Phono Audio Level Adjust: Trim pot adjust Power: 12V DC, 500 ma Audio Messages:4 messages, 15 seconds each CW Output keying: Solid state, for positive keyed rigs only Software compatibility: N1MM Logger, CT, NA, TR-LOG The VK-64-DX comes without a power supply for stations that use a different power connectors or otherwise want to supply their own 12VDC. Adding computer control only needs a standard 25 pin shielded computer cable between theĬables are not included, but can be easily made according to directions in the manual orĪ 12V wall transformer with US standard 2 prong plug is included with the VK-64. Transmitter, even when the VK64 is powered off.ĬW set up is as simple as plugging your paddle into the VK-64. Microphone audio and PTT signals pass through the VK-64 and connect directly to the Plug the microphone into the VK-64's microphone input cable.
It was built for running echolink and it worked well for that project. The ULI is an audio interface device I bought at the Dayton Hamfest several years ago.
Installing the VK-64 is easy! Unplug the microphone and plug the VK-64's transmitter audio/PTT cable New Wire Diagram using the ULI - allows N1MM to function as a voice keyer ULI Schematic (large 400k) the only thing really useful from their docs ULI Interface Connections. The VK-64 is compatible with the major contest logging programs, including N1MM Logger, NA, WriteLog, TRLog, CT and LogEQF. The delay time can be adjustedįrom approximately 1/2 to 12 seconds with a front panel control. Message 1 for both CW and voice modes can be set up for auto repeat. Logging programs support sending CW through the printer port.Ĭomputer keying works in parallel with the internal CW keyer. The VK-64 also includes a built in LPT CW interface. A front panel knob adjusts speed from 8-45 WPM. The CW portion is an iambic memory keyer with four programable messages, each one capable of storing over 300 Morse characters. Messages are stored in non-volatile memory, remaining stored until recorded over with a new message. Press the stop button when you are finished. Press the record button followed by a message number button and start talking. The voice keyer section has four 15 second messages. You can operate the VK64 manually with the front panel controls or under program control through your PC or laptop's printer port. The VK-64 is a voice keyer and CW memory keyer in the same package! This is a legacy product and is no longer available. Just thinking out loud.Unified Microsystems: W9XT VK-64 Combo Voice Keyer/CW Memory Keyer and more for ham radio operators! Looks like the migration of MAC SSDR to OSX 10.16 has killed any prospect of restoring this capability.Īs a workaround, would it be possible to add a button in your display to control DAX? This way it would still require two keystrokes but they would be in the same display. Just hit the audio file selection and sit back. The program’s original ability to assert and release DAX was very useful. Again, the program indicated that it could not find the file although the correct new address was listed. I listed this file and new address on the preferences pane. I made a dummy audio folder and transferred a copy of one of the audio files to it. When a file was selected, an error message indicated that the program could not find the audio file although it’s correct address was listed in the note. The preferences pane showed the same audio files as the previous version. DAX has to be set manually or no audio is transmitted. As a check, I ran 3.0.1 and it had the same problem, i.e.
0 kommentar(er)
